View MC10H352FN_744265.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MC10H352 Quad CMOS to PECL* Translator
Description
The MC10H352 is a quad translator for interfacing data between a CMOS logic section and the PECL section of digital systems when only a +5.0 Vdc power supply is available. The MC10H352 has CMOS compatible inputs and PECL complementary open-emitter outputs that allow use as an inverting/non-inverting translator or as a differential line driver. When the common strobe input is at a low logic level, it forces all true outputs to the PECL low logic state ( +3.2 V) and all inverting outputs to the PECL high logic state ( +4.1 V). The MC10H352 can also be used with the MC10H350 to transmit and receive CMOS information differentially via balanced twisted pair lines.
Features
http://onsemi.com MARKING DIAGRAMS*
20 MC10H352P AWLYYWWG PDIP-20 P SUFFIX CASE 738 1
* * * * *
Single +5.0 V Power Supply All VCC Pins Isolated On Chip Differentially Drive Balanced Lines tpd = 1.3 nsec Typical Pb-Free Packages are Available*
20 1 PLLC-20 FN SUFFIX CASE 775
1 20
10H352G AWLYYWW
A WL YY WW G
= Assembly Location = Wafer Lot = Year = Work Week = Pb-Free Package
*For additional marking information, refer to Application Note AND8002/D.
ORDERING INFORMATION
See detailed ordering and shipping information in the package dimensions section on page 4 of this data sheet.
*For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D.
(c) Semiconductor Components Industries, LLC, 2006
February, 2006 - Rev. 7
1
Publication Order Number: MC10H352/D
MC10H352
B OUT B OUT B IN A IN D IN 7 8 12 1 2 5 4 16 17 C IN 14 COMMON 9 STROBE 19 18 B OUT B OUT A OUT A OUT D OUT D OUT C OUT C OUT N.C. A OUT A OUT VCC B IN A IN COMMON STROBE GND 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 ECL VCC C OUT C OUT D OUT D OUT VCC 2 C IN N.C. D IN CMOS VCC
VCC (+5.0 VDC) = PINS 6, 11, 15, 20 GND = PIN 10
Figure 1. Logic Diagram
Pin assignment is for Dual-in-Line Package. For PLCC pin assignment, see the Pin Conversion Tables on page 18 of the ON Semiconductor MECL Data Book (DL122/D).
Figure 2. Pin Assignment
Table 1. MAXIMUM RATINGS
Symbol VCC VI Iout TA Tstg Power Supply Input Voltage (VCC = 5.0 V) Output Current Continuous Surge Characteristic Rating 0 to +7.0 0 to VCC 50 100 0 to +75 Plastic Ceramic -55 to +150 -55 to +165 Unit Vdc Vdc mA C C
Operating Temperature Range Storage Temperature Range
Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected.
http://onsemi.com
2
MC10H352
Table 2. ELECTRICAL CHARACTERISTICS (VCC = VCC1 = VCC2 = 5.0 V 5.0%) (Note 1)
0 Symbol ECL TTL IR Characteristic Power Supply Current Reverse Current Pins 7, 8, 12, 14 Pin 9 Forward Current Pins 7, 8, 12, 14 Pin 9 Input Voltage Breakdown Input Clamp Voltage (Iin = -18 mA) High Output Voltage (Note 2) Low Output Voltage (Note 2) High Input Voltage Low Input Voltage 3.98 3.05 3.15 1.5 5.5 -1.5 4.16 3.37 4.02 3.05 3.15 1.5 Min Max 50 20 25 100 -0.8 -3.2 5.5 -1.5 4.19 3.37 4.08 3.05 3.15 1.5 Min 25 Max 45 15 20 80 -0.6 -2.4 5.5 -1.5 4.27 3.37 Min 75 Max 50 20 25 100 mA -0.8 -3.2 Vdc Vdc Vdc Vdc Vdc Vdc Unit mA mA mA
IF
V(BR)in VI VOH VOL VIH VIL
*Positive Emitter Coupled Logic 1. Each MECL 10HTM series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 lfpm is maintained. Outputs are terminated through a 50 W resistor to VCC - 2.0 Vdc. 2. With VCC at 5.0 V. VOH/VOL change 1:1 with VCC.
Table 3. AC PARAMETERS
0 Symbol tpd tr tf fmax Characteristic Propagation Delay (Note 3) Rise Time (20% to 80%) Fall Time (80% to 20%) Maximum Operating Frequency Min 0.4 0.4 0.4 150 Max 1.9 1.9 1.9 Min 0.4 0.4 0.4 150 25 Max 2.0 2.0 2.0 Min 0.4 0.4 0.4 150 75 Max 2.1 2.1 2.1 Unit ns ns ns MHz
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 3. Propagation delay is measured on this circuit from VCC/2 on the input waveform to the 50% point on the output waveform.
http://onsemi.com
3
MC10H352
ORDERING INFORMATION
Device MC10H352FN MC10H352FNG MC10H352FNR2 MC10H352FNR2G MC10H352P MC10H352PG Package PLLC-20 PLLC-20 (Pb-Free) PLLC-20 PLLC-20 (Pb-Free) PDIP-20 PDIP-20 (Pb-Free) Shipping 46 Units / Rail 46 Units / Rail 500 / Tape & Reel 500 / Tape & Reel 18 Unit / Rail 18 Unit / Rail
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.
http://onsemi.com
4
MC10H352
PACKAGE DIMENSIONS
20 LEAD PLLC CASE 775-02 ISSUE E
B -N- Y BRK D -L- -M- W D V 0.010 (0.250) T L-M N Z 0.007 (0.180) M T L-M U
S
N
S S
0.007 (0.180) M T L-M
N
S
20
1
X VIEW D-D
G1
S
S
S
A Z R
0.007 (0.180) M T L-M 0.007 (0.180) M T L-M
S
N N
S
S
S
H K1
0.007 (0.180) M T L-M
S
N
S
C
E G G1 0.010 (0.250) S T L-M 0.004 (0.100) J -T- VIEW S
S SEATING PLANE
K F VIEW S 0.007 (0.180) M T L-M
S
N
S
N
S
NOTES: 1. DIMENSIONS AND TOLERANCING PER ANSI Y14.5M, 1982. 2. DIMENSIONS IN INCHES. 3. DATUMS -L-, -M-, AND -N- DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 4. DIMENSION G1, TRUE POSITION TO BE MEASURED AT DATUM -T-, SEATING PLANE. 5. DIMENSIONS R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 6. DIMENSIONS IN THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635).
DIM A B C E F G H J K R U V W X Y Z G1 K1
INCHES MIN MAX 0.385 0.395 0.385 0.395 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 --- 0.025 --- 0.350 0.356 0.350 0.356 0.042 0.048 0.042 0.048 0.042 0.056 --- 0.020 2_ 10 _ 0.310 0.330 0.040 ---
MILLIMETERS MIN MAX 9.78 10.03 9.78 10.03 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 --- 0.64 --- 8.89 9.04 8.89 9.04 1.07 1.21 1.07 1.21 1.07 1.42 --- 0.50 2_ 10 _ 7.88 8.38 1.02 ---
http://onsemi.com
5
MC10H352
PACKAGE DIMENSIONS
PDIP-20 P SUFFIX PLASTIC DIP PACKAGE CASE 738-03 ISSUE E
-A-
20 1 11 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. DIM A B C D E F G J K L M N INCHES MIN MAX 1.010 1.070 0.240 0.260 0.150 0.180 0.015 0.022 0.050 BSC 0.050 0.070 0.100 BSC 0.008 0.015 0.110 0.140 0.300 BSC 0_ 15 _ 0.020 0.040 MILLIMETERS MIN MAX 25.66 27.17 6.10 6.60 3.81 4.57 0.39 0.55 1.27 BSC 1.27 1.77 2.54 BSC 0.21 0.38 2.80 3.55 7.62 BSC 0_ 15_ 0.51 1.01
B
10
C
L
-T-
SEATING PLANE
K E G F D
20 PL
N J 0.25 (0.010)
M 20 PL
M
0.25 (0.010) TA
M
M
TB
M
MECL 10H is a trademark of Motorola, Inc.
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT: N. American Technical Support: 800-282-9855 Toll Free Literature Distribution Center for ON Semiconductor USA/Canada P.O. Box 61312, Phoenix, Arizona 85082-1312 USA Phone: 480-829-7710 or 800-344-3860 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center 2-9-1 Kamimeguro, Meguro-ku, Tokyo, Japan 153-0051 Fax: 480-829-7709 or 800-344-3867 Toll Free USA/Canada Phone: 81-3-5773-3850 Email: orderlit@onsemi.com ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder For additional information, please contact your local Sales Representative.
http://onsemi.com
6
MC10H352/D

▲Up To Search▲

Price & Availability of MC10H352FN

	To Download MC10H352FN Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .